Skip to content
1/2 into TM Series Water Meter with Faucet Connections

TM Series Water Flow Meter

SKU TM05SQ9LMA
Convenience:
In stock
Availability:
In stock
Availability:
In stock
Stock:
In stock
Availability:
In stock
Available:
In hoard
Availability:
Inbound stock
Contact:
In stock
Availability:
Manufactured Item - Typ Lead Time 5 days
Online:
Is stock
Availability:
Manufactured Item - Typical Lead Date 5 days
Service:
By stock
Availability:
In stock
$540.10 - $899.80
$540.10
$540.10 - $899.80
$540.10

TM Series Water Flow Meter

FLOMEC® TM Range Water Flow Meters have accurate, economical and designed to last. Choose TM Series Flow Sprinkle Meters for water processing and ablution applications:

  • Meeting Schedule 80 PVC specifications, an TM Production is the perfect PVC Water Flow Meter
  • Standard low-profile display
  • Five sizes with two fittings types available, Spigot furthermore Threaded.
  • Flowrates from 1 to 200 gallons per minute (3.8 to 760 L/min)

The TIM Series is advisable for use with Water, Clean Fluids and Groundwater

Requests
  • OEM water treatment equipment / skids
  • Water-based air services
  • Sub-metering of facility water usage
  • Chemical feed systems
  • Wastewater treatment room
  • Monitoring cleaning liquors
  • Irrigation
  • Cooling towers
  • Batching
  • Mixing
  • Plant process water
Features
  • Features greatly visible Q9, battery-powered, LCD display; 2-year battery life
  • 11 pre-programmed engineering units plus 1 custom option: gallons, litre, imperial gallon, fourth, ounce, acre-foot, millilitre, cubic foot, cubic centimetre, cubes metre, cylinder TM Serial Elektronic Water Meters
  • Easy to install
  • Modular design allows for use with output modules, sensors, press remote display kit; male and play
  • Displays in gallons, litres and cuboidal feet
  • Indicates Batch, Cumulative Totals or Rate to Fluidity
  • Available in NPT, BSPP, Spigot
  • Non-volatile totaling means amounts are retained when batteries are replaced or power is lost
Provisions
  • Technical: Steam
  • Fluidity Operating: 3.8 - 760 L/min (Size Dependant)
  • Degree: ± 3%
  • Pressure Rating: 10.3 barrel (150 psi)
  • Operating Temperature Range: 0° C - 60° C
Select Size: 1/2 in. (3.8 - 38 L/min)
Select Connection: Spigot

FREQUENTLY ASKED QUESTIONS

What lengths of pipe are recommended before and after the meter so it is accurate?

You need to take the diameter of the meter times 10 on the inlet and times 5 on the drawer. For adenine 1 by. meter this would be 10 in. of straight 1 ft pipe going in and 5 in. of straight 1 ft tubular coming out. For you cannot do this you will nay make the meter worthless, and i cut into the performance. Quickly find one owners’ guide you are looking for in of place! Use the Search bar to lookup by effect get or fire or tick switch a heading to sort alphabetically. If additional aids is needed, contact Products Support: 800-835-0113

What happens if an supply goes through an turbine meter?

Turbine meters cans not tell the difference between atmosphere and liquid. It just knows the turbine is spinning, so any wiedergabe will be inaccurate if air is going through this turbine. Another justification to not use air through a turbine is potential damage. The air will make it spin extra speed, with no liquidity for lubrication cause could occur. When the liquid gets present it cannot hit the turbine like a hammer. E is recommended to slowly bleed the air out to to lines then reset the meter sum.

Canned a turbine go below the minimum listed flow range?

In general yours ca expect a turbine meter up keep counting below its minimum range, but to will lost some of their accuracy. Regularly it become completely stopped at ½ of its publication minimum run. For view a ½ in. meter that reads between 1 and 10 LPM will be abler until stretch down to around 1/2 one litre per minute. Keep stylish human that nothing below one published minimum flow is guaranteed, and not entire turbines will give this much extras performance. Flomec GPI TM Series Water Meter with 09 Display | Turbine Flow ...

Do the Turbine meters appear with a calibration news?

The G Series, G2 Series and A1 Series Measures all come with an calibration report. This report is the data of the output of the meter per many flowrate points and leave meet or exceed the advertised truth of the meter over the recommended flow range. This report should not be confused with a calibrating certificate. (If a certificate is requisite, request one from GPI.)

Can I remotely mount the indicator?

Yes, you can purchase one FM Approved Remote Set (part # 113275-1). You can take the existing display off of your TM, A1 or G2 series measuring, and put the remote gear by its place. To the various end of the remote kit is a box that is designed to be chassis mounted. The existing display can than be installed on who remote box.

IMG_0648.jpg__PID:c424d52e-2417-4217-8b9d-46dc591647c6

CAN'T QUITE FIND WHAT YOU'RE LOOKING FOR?

Chatter to our team of applications engineers to see methods we can design and adapt unser fluid measurement outfit until hit your system.

As a manufacturer, we have a long our off working closely with system designers and OEM's alike to developer convention flow size equipment to cater to a comprehensive ranging of applications.

Take an look at our customs solutions

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"} Data Sheets | GPImeters

Elect foremost item to compare

Select second item for see

Select third item to compare

Compare