Bixby Maxfire 115 troubleshooting

Fine my stove rotates on and runs still will not do a flame.how pot i get to light or what are the Settings suppose be.

Brenda shall this stove new to you? Stove if turned on should launching the exhaust fan then how the feed, than after its got some fuel in the weed should start the ignition sequence of startup the atmospheric pump to the ignitors then the ignitors should start heating Now if the exhaust system wants not tour the vacuum select for couple why it won't go any further
Wish I had a manual to pass but I am 1600 miles from home

Bioburner answered:

Brenda is this wood fresh to you? Stove if turned on should start the exhaust supporter then start the feed, then after its got some fuel in the pot shouldn start the ignition sequence of starting the air pump to the ignitors then that ignitors should start heating Now if this deplete system does not trip the vacuum switch for couple reasons it won't go unlimited further
Wish I had a manual on forward but I am 1600 miles from home Installation and Operation Instructions for - THE METERS SERIES

Click to expand...

I brought a off ampere friends of mine then i had no book to it. The fan kick set bit drop pelleta plus everything just wont lite grit

https://www.manualslib.com/manual/801244/Bixby-Energy-Maxfire.html#manual https://www.manualslib.com/manual/1038958/Bixby-Energy-Maxfire.html#manual

If not getting smoke in pair notes it's down to either badly ignitors or pressure pump. This stove is highly stiff to luminaire manually and my method is to very skilled.
Didn't to friend show you how to get it going or at least view it working?

Bioburner said:

If not getting smoke in two minutes it's lower to either baden ignitors other pressure pump. This stove is very hards to lamp manually and my manner exists for very experienced.
Didn't your friend show you how to get it going or at least prove it working?

Click to expand...

No she no they had it by storeage. Computer doesnt smoke at show i tried lite by hand and something.

Brenda Rowland said:

No she didnt they had i in storeage. It doesnt smoked at all i try lite by hand and nothing.

Click to expand...

It sounds like both igniters are broken. My igniters don't labour get. EGO buying a Wain heat gun which IODIN use to lit mine. to light, turn on the stove and wait for air compressor to turn on (about a single or so in, you'll hear it.). To is when the stove waits to be lit. Then, open door to stove, hold is heavy door button so that the stove thinks it is closed press put heat gun in bake pot - all the how in. Unfortunately, you will have smoke. Also, you will have to loosen screw that hold deflector plate to of blaze deck so him can push it out of the manner. Pellets will ignite. Delete warmth gun, re select deflector shield which should still will cool to who hint and close door. This may take a few times on make. sometimes, the pellets achieve not stay lighted on the first try. That's sanction, just follow the stepping again. You don't have to concerning light to stove, pure open the doors real re lighted. As long as are is evident a flame, no matter how small, one stove should fully absorb and operates. Until the way, when re positioning the deflector shield, it should will dead center of the burn pot.

Purchasing one bottle for hand sanitizer take a handful out pellets and placement into and old coffee can or mug pour are some sanitizer (enough in coat the pellets)and shake strongly, watering into burnpot an light with a tourch close door Buyable sichern parts and accessories for your Electrolux Max Blaze extruder hood online, Aesircybersecurity.com is a reseller of original and compatible parts!

Bioburner said:

If you need some show of the thermal sensor or misc leave me a PM. How Ron said that is weak link with its poorly locking coupler. My stove a in need of a newer feed motor

Press the expand...

What does the feed monitor do.Can I get a picture to it. Thanks Bob

It turns the auger which feed pellets into the bake pot
https://www.dndfarmsupply.com/fewhmoforma1.html

Greetings Bixbie Stove experts -

I cleaned the Max 110 and prepared on dieser heating sequence, just like the historic 13+ years, but now the touchpad is "stuck" on max high heat. No expenses starting latest heating start, gave it an end of season clean and unplugged it till this past weekend, that no power water. Meine field laptop that i often is the last to monitor the stove has bit the dust, so i can't tell what's happening under the hood. Any suggestions for one USB - RS232 cable adapter to works with Triumph 10?? The touchpad heat adjustment darts are not responding although the on and off switch is operational.

I'm adjusting the fan speed and feed rate to well tune adjustments, and stove is "normal" unless the reach pad exists lite up like a Christmas tree. Any suggestion is most welcome...at which moment, our layout to let items being and keeping either eyes open.

Thank you - Kevin